From the first phone call to the final safety test, Allstar garage door sensor repair in Evansville, WY follows a simple process: diagnose, quote, repair, test. Photo-eye sensors realigned, rewired or replaced so the door closes reliably. Whether your Allstar opener is a few years old or a few decades, we can diagnose it and tell you honestly whether it is worth repairing. Allstar openers are no longer made. Replacement remotes and many parts are still available, and we'll tell you when replacing the opener makes more sense.
Signs you need Allstar garage door sensor repair
- The door goes back up right after it starts closing
- Sensor lights are blinking or off
- The door only closes when you hold the wall button
- The opener light flashes when you try to close
Common causes
- Sensors bumped out of alignment
- Dirty lenses or direct sunlight
- Damaged or loose wiring
- Failed sensors
What you can check yourself
- Wipe both lenses with a soft cloth.
- Adjust the brackets until both indicator lights are steady.
- Look for staples or damage on the thin sensor wires.
Still stuck? Our free symptom checker and troubleshooting wizard walk you through it step by step.
What happens during the visit
- Test the sensor voltage and wiring
- Realign or replace the sensors
- Repair or replace the wiring
- Shade sensors from direct sun if needed
- Test the auto-reverse
How much does Allstar garage door sensor repair cost?
What moves the price:
- Drive type: chain, belt, screw or wall-mount
- Whether the fix is a part or a whole new opener
- Remotes, keypads and smart accessories
- Ceiling height and rail extensions
These are typical U.S. ranges, not a quote. You get an exact price for your door before any work starts. For a quick estimate, try the repair cost calculator.
Other Allstar services
- Allstar Garage Door Opener Repair
- Allstar Remote & Keypad Programming
- Allstar Opener Gear & Sprocket Replacement
- Allstar Opener Circuit Board Replacement
Allstar Garage Door Sensor Repair in Evansville, WY
Rapid temperature changes in Wyoming can throw off opener travel limits, and cold mornings make a weak opener struggle with a door that is out of balance.
Technicians serve all of Evansville (ZIP code 82636), plus Casper (2.3 mi), Mills (5.1 mi), Bar Nunn (5.3 mi) and Glenrock (20.1 mi). Call (833) 435-8883 to book a visit in Evansville.
Allstar Garage Door Sensor Repair: frequently asked questions
How much does Allstar garage door sensor repair cost in Evansville, WY?
Allstar Garage Door Sensor Repair typically costs $100-$250 including parts and labor, and usually takes about 1 hour. The exact price depends on your door and the parts it needs, and you get it before any work starts. Call (833) 435-8883 for a quote.
Can you do Allstar garage door sensor repair the same day?
Often, yes. When a technician is available we can usually come the same day, and common parts are carried on the truck. Doors that won't close or have a broken spring are treated as priority calls, and emergency service is available.
Is Allstar garage door sensor repair covered by a warranty?
Our work comes with a 90-day labor warranty on repairs. New parts and doors also carry the manufacturer's warranty, and Allstar warranty terms vary by product and age. Ask for the warranty details in writing with your quote.
Are your technicians licensed and insured?
Our technicians are insured, and where Wyoming or Evansville requires a contractor license for garage door work, the job is done under that license. You're welcome to ask for proof when you book.
Should I repair or replace my opener?
A good rule of thumb: if the repair costs more than about 50% of a replacement, or the opener is near the end of its life, replace it. Most openers last 10 to 15 years. If yours is older than that, lacks photo eyes or rolling-code security, or needs a logic board or motor, a new opener is often better value. Springs are the exception: a broken spring is always replaced, never repaired. Our free repair vs. replace calculator can help you compare.